Concrete Footing Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
Continuous vs. pad footings
Continuous (strip) footings run under walls such as a house foundation, garage, addition or block wall. Enter the total length of every run added together, plus the width and depth of the trench or form.
Pad (spread) footings are square or rectangular blocks under individual columns or posts: porch columns, carport posts, beam supports in a crawlspace. Enter one pad's size and how many you need.
The formula
Cubic yards = length (ft) × width (ft) × depth (ft) ÷ 27. Convert inches to feet by dividing by 12. The calculator then adds your waste percentage, rounds up to the next quarter-yard for ready-mix (how most US plants sell it), and converts to 40, 50, 60 and 80 lb bags.
Concrete per linear foot of footing
| Footing (W × D) | Cu ft per foot | Feet per cubic yard |
|---|---|---|
| 12 × 6 in | 0.5 | 54 ft |
| 16 × 8 in | 0.889 | 30.4 ft |
| 20 × 8 in | 1.111 | 24.3 ft |
| 20 × 10 in | 1.389 | 19.4 ft |
| 24 × 10 in | 1.667 | 16.2 ft |
| 24 × 12 in | 2 | 13.5 ft |
Example: a 24 × 30 ft garage
Perimeter = 2 × (24 + 30) = 108 ft. A 16 × 8 in. footing holds 0.889 cu ft per foot, so 108 ft is 96 cu ft or 3.56 yd. With 8% waste that's 3.84 yd, so you'd order 4 yards. Two #4 bars the full length with 10% for laps = 238 ft, or 12 twenty-foot sticks.
How rebar and forms are estimated
- Continuous footings: number of bars × length, plus 10% for lap splices at joints and corners.
- Pad footings: a grid each way at your spacing, held 3 in. in from every edge (standard cover against soil).
- Form boards: both sides of a strip footing, or the perimeter of each pad. Skip them if you pour straight into a clean, firm trench and your inspector allows it.
Before you pour
- Get the footing inspection. Most jurisdictions require it before concrete is placed.
- Remove loose soil and standing water from the bottom of the trench; footings must bear on undisturbed soil.
- Support rebar on chairs or concrete dobies so it ends up inside the concrete, not lying on the dirt.
- Set anchor bolts or vertical dowels while the concrete is wet if a wall goes on top.
Pouring round piers instead? Use the Sonotube calculator. For deck posts, the deck footing calculator sizes the footing from the deck's load.
Frequently asked questions
▸How do you calculate concrete for a footing?
Multiply length × width × depth in feet to get cubic feet, then divide by 27 for cubic yards. A 100 ft footing that is 16 in. wide and 8 in. deep is 100 × 1.333 × 0.667 = 88.9 cu ft, or 3.29 cubic yards before waste.
▸How big should a footing be for a house?
Under the IRC, footings must be at least 12 in. wide and 6 in. thick, and wider for heavier homes or weaker soil (IRC Table R403.1). 16 to 24 in. wide by 8 to 12 in. thick is common. Your plans or local building department set the final size.
▸How much rebar goes in a footing?
Residential continuous footings commonly get two #4 bars running the full length, lapped about 24 in. at splices and kept 3 in. off the soil. Seismic zones and engineered plans often require more.
▸How much does a yard of concrete cost?
Ready-mix pricing varies by region and season, and small loads usually carry a short-load fee. Call two local suppliers for a delivered price and enter it in the calculator to estimate your cost.
▸How much extra concrete should I order for footings?
Add 5 to 10%. Trench-poured footings vary in width and depth more than forms do, so lean toward 10% when pouring straight into dug trenches.
▸How deep do footings need to be?
The bottom of the footing must be below the frost line, which ranges from about 12 in. in the warmest parts of the US to 48 in. or more in northern states. Your local building department publishes the required depth.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.