Gravel Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
How to calculate gravel
- Area: length × width for rectangles, 3.1416 × radius² for circles, ½ × base × height for triangles.
- Volume: area × depth in feet (inches ÷ 12) = cubic feet; ÷ 27 = cubic yards.
- Weight: cubic yards × about 1.4 = tons (most gravel runs 1.3–1.7).
- Compaction: add about 10–15% for crushed stone that will be compacted.
Tons of gravel by area and depth
At 1.4 tons per cubic yard, no compaction allowance:
| Area | 2 in deep | 3 in deep | 4 in deep | 6 in deep |
|---|---|---|---|---|
| 100 sq ft | 0.9 t | 1.3 t | 1.7 t | 2.6 t |
| 200 sq ft | 1.7 t | 2.6 t | 3.5 t | 5.2 t |
| 500 sq ft | 4.3 t | 6.5 t | 8.6 t | 13 t |
| 1,000 sq ft | 8.6 t | 13 t | 17.3 t | 25.9 t |
How deep should gravel be?
| Use | Typical depth |
|---|---|
| Gravel driveway | 4–6 in. (8–12 in. on soft soil, in layers) |
| Walkway or garden path | 2–3 in. |
| Pea gravel patio | 3 in. |
| Base under pavers or a shed | 4–6 in. compacted |
| Landscape / decorative beds | 2–3 in. |
| French drain / drainage | fill the trench (see French drain calculator) |
Choosing the right gravel
- Crusher run / road base: crushed stone with fines that packs hard. Best for driveway bases and under pavers.
- #57 or 3/4 in. clean crushed stone: drains well. Good for driveway top layers, shed pads and drainage.
- Pea gravel: smooth and comfortable underfoot for patios, paths and play areas, but it shifts; edge it well.
- River rock: decorative beds and dry creek beds.
Gravel project calculators
- Shed foundation calculator: gravel pad with timber frame, or a slab or blocks.
- French drain calculator: drain rock, pipe and fabric for a trench.
- Retaining wall calculator: base and drainage gravel behind a block wall.
- Concrete calculator: when the job needs concrete instead.
Frequently asked questions
▸How do I calculate how much gravel I need?
Multiply length × width (ft) for square feet, multiply by depth in feet (inches ÷ 12) for cubic feet, and divide by 27 for cubic yards. Multiply cubic yards by about 1.4 for tons. A 12 × 50 ft driveway at 4 in. deep is 200 cu ft, or 7.4 yd, which is about 10.4 tons before compaction.
▸How many tons of gravel do I need for a driveway?
For a typical single-car driveway 12 ft wide and 50 ft long at 4 in. deep, plan about 11–12 tons including compaction. Driveways on soft soil need 8–12 in. built up in layers, which can triple that.
▸How much does a cubic yard of gravel weigh?
Most gravel weighs about 1.3 to 1.7 tons (2,600–3,400 lb) per cubic yard, depending on stone type and moisture. 1.4 tons is a common figure for crushed stone, but ask your supplier for their number.
▸How much area does a ton of gravel cover?
At about 1.4 tons per cubic yard, one ton covers roughly 115 sq ft at 2 in. deep, 77 sq ft at 3 in., or 58 sq ft at 4 in.
▸Is it cheaper to buy gravel in bags or bulk?
Bulk is almost always cheaper above a ton or two. A 0.5 cu ft bag holds only about 1/54 of a cubic yard, so a single ton is roughly 40 bags. Bulk suppliers often charge a delivery fee, which the calculator includes.
▸How deep should gravel be?
2–3 in. for paths and decorative beds, 3 in. for a pea gravel patio, 4–6 in. compacted for a driveway or a base under pavers or a shed.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.