Deck Footing Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
How deck footings are sized
Every deck footing does one job: spread the weight on a post over enough soil that the soil doesn't compress. The calculator follows the same load path an inspector or engineer uses:
- Tributary width. On a ledger-attached deck, the house carries half the joist span and the beam carries the other half, plus any cantilever past the beam.
- Tributary area. Multiply by the post spacing along the beam to get the square feet of deck each interior post holds up.
- Load. Multiply by the design load: 40 psf live (IRC) + 10 psf dead for a typical wood deck.
- Footing area. Divide by the soil's allowable bearing pressure (1,500 psf is the IRC presumptive value for clay and silt, and the safe default when you don't know).
- Round up to the next standard tube diameter, or to a square pad in 2 in. steps.
Soil bearing values
These are the IRC presumptive values (Table R401.4.1) used when no soil test has been done:
| Soil | Allowable bearing |
|---|---|
| Clay, sandy clay, silty clay, silt (CL, ML, MH, CH) | 1,500 psf |
| Sand, silty sand, clayey sand, silty or clayey gravel (SW, SP, SM, SC, GM, GC) | 2,000 psf |
| Sandy gravel and gravel (GW, GP) | 3,000 psf |
If you aren't sure, use 1,500 psf. It's the most conservative and the one most inspectors expect.
Example: a 16 × 12 ft deck attached to the house
One beam at the outside edge, posts at 8 ft max → 3 posts at 8 ft. The beam carries half of the 12 ft joist span = 6 ft. An interior post supports 6 × 8 = 48 sq ft × 50 psf = 2,400 lb. On 1,500 psf soil that needs 1.6 sq ft of footing: an 18 in. round pier or a 16 × 16 in. pad. Tightening the post spacing to 5.33 ft (4 posts) drops the load to 1,600 lb and the pier to 14 in.
Round pier or pad-and-pier?
A full-depth round pier (one Sonotube from the hole bottom to above grade) is simple but uses a lot of concrete when you need a big diameter. A square pad with a narrower pier on top puts the wide part only at the bottom where it's needed, which often uses far less concrete for big footings. Plastic bell-shaped footing forms do the same job in one piece.
Things this calculator doesn't cover
- Hot tubs, roofs over the deck, or second-story decks with stairs landing on them. These need engineered footings.
- Expansive clay, fill soil, or slopes, where a soils report may be required.
- Beam and joist sizing. Check IRC R507 span tables or your local deck guide.
Have your footing size? Get the exact concrete for a different tube setup with the Sonotube calculator, or price a continuous footing with the concrete footing calculator.
Frequently asked questions
▸How big do deck footings need to be?
Big enough that the load on each post divided by the footing area stays under your soil's allowable bearing pressure. For example, a post carrying 2,400 lb on 1,500 psf clay needs 1.6 sq ft of footing, an 18 in. round pier or a 16 × 16 in. pad. Larger post spacing or deeper decks need bigger footings.
▸How far apart should deck footings be?
Usually 6 to 8 ft along the beam for typical doubled or tripled 2×10 and 2×12 beams. Wider spacing means fewer holes but bigger beams and bigger footings. Check the beam span tables in IRC R507 or your local deck guide.
▸How deep should deck footings be?
Below the frost line and at least 12 in. below undisturbed soil. That's roughly 12 in. in the Deep South, 30 to 36 in. in much of the mid-Atlantic and Midwest, and 42 to 60 in. in northern states. Some jurisdictions allow freestanding decks on shallower footings. Ask your building department.
▸What load should I use for a deck?
The IRC requires decks to support a 40 psf live load. Wood decks are typically designed for 10 psf dead load. Use a higher live load where the ground snow load exceeds 40 psf, and a higher dead load for composite decking, stone, or a hot tub (which needs its own engineered support).
▸Do I need a permit for deck footings?
Most US jurisdictions require a permit for decks attached to a house or more than 30 in. above grade, and an inspection of the footing holes before concrete is poured.
▸Can I use deck blocks instead of footings?
Precast deck blocks sitting on the surface are generally only accepted for low, freestanding decks where local code allows. Attached decks almost always need frost-protected footings.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.