French Drain Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
How a French drain works
A French drain is a gravel-filled trench, usually with a perforated pipe in the bottom, that gives ground water an easy path away from a soggy lawn, a basement wall or a driveway. Water seeps into the gravel, drops into the pipe and runs downhill to an outlet: a dry well, a daylight point lower on your lot, or a storm drain where your city allows it.
Gravel needed for a French drain (12 × 18 in. trench, 4 in. pipe, 1% slope)
| Trench length | Gravel | Tons (approx.) | Fabric | Outlet depth |
|---|---|---|---|---|
| 25 ft | 1.31 yd | 1.8 t | 151 sq ft | 21 in |
| 50 ft | 2.88 yd | 4 t | 315 sq ft | 24 in |
| 75 ft | 4.7 yd | 6.6 t | 492 sq ft | 27 in |
| 100 ft | 6.77 yd | 9.5 t | 683 sq ft | 30 in |
| 150 ft | 11.69 yd | 16.4 t | 1,103 sq ft | 36 in |
How the calculator works
- Slope: length × slope % gives the drop, so the trench deepens toward the outlet. The average depth is used for volume.
- Gravel: trench volume to about 3 in. below grade, minus the pipe, plus waste. Washed stone is figured at about 1.4 tons per cubic yard; ask your supplier, as it varies.
- Fabric: enough to line both sides and the bottom and fold over the top with a 12 in. overlap.
- Pipe: trench length + 5%, in 10 ft rigid lengths or 100 ft corrugated rolls.
Example: a 50 ft yard drain
12 in. wide, starting 18 in. deep with 1% slope, the trench ends 24 in. deep. You need about 4 tons (2.88 yd) of drain rock, 6 ten-foot lengths of 4 in. perforated pipe and 315 sq ft of fabric, and you'll dig out about 4.1 cubic yards of soil.
Building it, step by step
- Call 811 at least a few days before digging. It's free and required.
- Mark the route from the wet area to the outlet and check the fall with a string line and level.
- Dig the trench, keeping the bottom sloped evenly. A rented trencher saves a lot of time on long runs.
- Line it with non-woven fabric, add 2–3 in. of gravel, and lay the pipe with the holes down.
- Fill with gravel to about 3 in. below grade, fold the fabric over, and top with soil and sod or decorative stone.
Wet ground around a shed or patio? Plan a well-drained base with the shed foundation calculator.
Frequently asked questions
▸How much gravel do I need for a French drain?
Multiply trench length × width × depth (in feet) for cubic feet, subtract the space the pipe takes, and divide by 27 for cubic yards. A 50 ft trench 12 in. wide and 18–24 in. deep with a 4 in. pipe needs about 2.9 cubic yards, or roughly 4 tons of washed stone.
▸How deep and wide should a French drain be?
Most yard French drains are 6–12 in. wide and 18–24 in. deep. Foundation drains go deeper, down to the footing. The trench should get deeper toward the outlet so the water runs downhill.
▸How much slope does a French drain need?
At least 1% (1/8 in. drop per foot), and 1–2% is typical. Over 100 ft that's 1 to 2 ft of drop, so check that your outlet is low enough before you dig.
▸What size gravel is best for a French drain?
Clean, washed 3/4 to 1-1/2 in. crushed stone or drain rock. Avoid pea gravel with fines or crusher run (it packs solid and clogs), and avoid limestone screenings.
▸Should the holes in French drain pipe face up or down?
Down. Water rises from below into the gravel and enters the pipe through the bottom holes, which keeps the pipe from filling with sediment from above.
▸Do I need landscape fabric for a French drain?
Yes, use non-woven geotextile (not plastic weed barrier). Line the trench and fold it over the gravel to keep soil from washing in and clogging the drain.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.