Concrete Wall & Block Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
Concrete block (CMU) walls
Standard concrete blocks are 8 × 8 × 16 in. nominal (7-5/8 × 7-5/8 × 15-5/8 in. actual). With a 3/8 in. mortar joint each block covers 0.889 sq ft of wall, so you need 1.125 blocks per square foot. The calculator adds your breakage allowance, counts mortar at about 13 blocks per 80 lb bag, and uses the NCMA grout table for the cores you fill.
Blocks, mortar and grout for a 4 ft wall
8 in. block, cores grouted at 32 in. on center, 5% extra block:
| Wall length | Blocks | Mortar (80 lb) | Grout |
|---|---|---|---|
| 10 ft | 48 | 4 bags | 3.6 cu ft (7 bags) |
| 20 ft | 95 | 8 bags | 7.3 cu ft (13 bags) |
| 40 ft | 189 | 15 bags | 14.6 cu ft (25 bags) |
| 60 ft | 284 | 22 bags | 21.8 cu ft (37 bags) |
| 100 ft | 473 | 37 bags | 36.4 cu ft (61 bags) |
Grout per 100 sq ft of 8 in. block wall
From the NCMA estimating table (TEK 4-2A), 3% waste included:
- Every core grouted: 36.1 cu ft
- Cores at 16 in. on center: 18.1 cu ft
- Cores at 24 in. on center: 12.1 cu ft
- Cores at 32 in. on center: 9.1 cu ft
- Cores at 48 in. on center: 6.1 cu ft
Poured concrete walls
Volume is length × height × thickness. The calculator adds your waste allowance, rounds ready-mix to the next quarter yard, and estimates a rebar grid at your vertical and horizontal spacing with about 10% for laps. Foundation walls are usually at least 8 in. thick; the IRC tables set thickness and reinforcement by wall height and soil.
Building tips
- Every wall needs a footing. Size it with the concrete footing calculator.
- Lay the corners first and run a mason's line between them for each course.
- Grout in lifts of 5 ft or less and consolidate each lift.
- Walls holding back soil behave very differently from free-standing walls. Over 4 ft, get an engineered design.
Frequently asked questions
▸How many concrete blocks do I need?
Multiply the wall's area in square feet by 1.125. A standard 8×8×16 block with a 3/8 in. mortar joint covers 0.889 sq ft. A 40 ft × 4 ft wall (160 sq ft) needs 180 blocks, or 189 with 5% extra for breakage and cuts.
▸How much mortar do I need for a block wall?
About one 80 lb bag of Type S mortar for every 13 standard 8×8×16 blocks, per manufacturer guidance. Thick joints or full mortar bedding use more.
▸How much grout to fill concrete block cores?
For 8 in. hollow block, the NCMA estimating table (TEK 4-2A) gives about 36 cu ft of grout per 100 sq ft of wall when every core is filled, and about 9 cu ft per 100 sq ft when only cores at 32 in. on center are grouted (3% waste included).
▸How much concrete for a poured wall?
Multiply length × height × thickness in feet and divide by 27. A 30 ft long, 8 ft high, 8 in. thick foundation wall is 160 cu ft, or about 5.9 cubic yards before waste.
▸Block wall or poured concrete wall, which is better?
Poured walls are faster to build and more water-resistant, but need formwork and a ready-mix truck. Block walls need no forms, are easier for DIY, and can be built a little at a time, but take more labor and must be grouted and reinforced for structural use.
▸Do block walls need rebar?
Short garden walls often don't. Foundation walls, retaining walls and walls in seismic or high-wind areas usually need vertical rebar in grouted cores, sized by code or an engineer.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.