Fence Calculator
</> Embed this calculator on your website: free
Contractors, suppliers and bloggers: paste this code into any page to give your visitors this calculator. It's free, needs no sign-up and stays up to date.
Wood privacy and picket fences
A stick-built wood fence is posts set in concrete every 6–8 ft, 2×4 rails between them, and pickets nailed or screwed to the rails. For a straight 100 ft run, 6 ft tall, with 1×6 privacy pickets:
| Item | Quantity |
|---|---|
| 4x4 posts, 10 ft (set 45 in. deep) | 14 |
| 2×4 rails, 8 ft (3 per section) | 39 |
| Pickets, 5.5 in. × 6 ft (privacy) | 219 |
| Exterior screws or ring-shank nails for pickets | 1314 |
| Rail brackets or structural screws | 78 |
| 50 lb fast-setting concrete | 89 |
| Gravel for post holes (0.5 cu ft bags) | 10 |
| Post caps | 14 |
Chain link fence parts explained
- Terminal posts: the heavier posts at ends, corners and gates, where the fabric is stretched from.
- Line posts: lighter posts between terminals, no more than 10 ft apart.
- Top rail: runs along the top through loop caps on the line posts; swaged sticks slide into each other.
- Tension bar + tension bands: the flat bar is woven through the fabric's end and clamped to the terminal post with bands.
- Brace bands + rail end cups: hold the top rail to each terminal post.
- Ties: aluminum wires that fasten the fabric to line posts and top rail.
Example: a U-shaped 4 ft chain link fence
Sides of 100, 50 and 100 ft against the house, with one 4 ft walk gate:
| Item | Quantity |
|---|---|
| Chain link fabric, 4 ft × 50 ft rolls | 5 |
| Terminal posts (end, corner & gate) | 6 |
| Line posts | 21 |
| Top rail, 21 ft sticks | 12 |
| Tension bars | 8 |
| Tension bands | 24 |
| Brace bands | 8 |
| Rail end cups | 8 |
| Carriage bolts & nuts | 32 |
| Terminal post caps (dome) | 6 |
| Line post loop caps | 21 |
| Fence ties (aluminum) | 207 |
| Gates, 4 ft (with hinges & latch) | 1 |
How the estimate is calculated
- Each side is split evenly with line posts no more than 10 ft apart (or one post per panel for panel fences).
- Terminal posts go at both ends of an open fence, every corner, and both sides of every gate.
- Fabric and top rail cover the fence length minus gate openings; rail allows ~6 in. overlap per swaged joint.
- Fittings are counted per terminal: corners need two tension bars and two rail ends, ends and gate posts need one.
Wood and vinyl panel fences
Pre-built panels set the post spacing for you, so the count is mostly panels and posts, plus brackets (two per rail per panel) and post caps. When a side isn't an exact multiple of the panel width, the last panel gets cut down, so the estimate includes full panels to cut from.
Next steps
Mark each post location with the fence post spacing calculator, then get hole depth, hole size and bags of concrete from the fence post depth calculator. Check your property line, HOA rules and local height limits before ordering, and call 811 before you dig.
Frequently asked questions
▸How do I calculate materials for a wood fence?
Split each side into sections no wider than 8 ft and add a post at every section end, corner and gate. Each section needs 2 rails (3 for a 6 ft fence), and pickets = fence length in inches ÷ (picket width + gap). A 100 ft, 6 ft privacy fence with 1×6 pickets needs about 14 posts, 39 rails and 219 pickets.
▸How many pickets do I need for a privacy fence?
Divide the fence length in inches by the picket width. With standard 5.5 in. pickets and no gap, that's about 2.2 pickets per linear foot, or 18 per 8 ft section.
▸How many bags of concrete per fence post?
For a 4×4 post on a 6 ft fence, set 3 ft deep in an 11 in. hole, it's about 1.7 cu ft of concrete, or 5 bags of 50 lb fast-setting mix. The calculator works this out for your height and post size.
▸What materials do I need for a chain link fence?
Fabric (sold in 50 ft rolls), terminal posts at every end, corner and gate, line posts about every 10 ft, top rail, and the fittings: a tension bar at every place the fabric ends, tension bands to hold each bar, brace bands and rail end cups for the top rail, post caps, carriage bolts and aluminum ties.
▸How many tension bands do I need?
About one less than the fence height in feet for each tension bar: 3 for a 4 ft fence, 5 for a 6 ft fence. Corner posts get two tension bars (one each direction), end and gate posts get one.
▸How far apart are chain link line posts?
No more than 10 ft apart, center to center. The calculator spaces them evenly on each side so you don't end up with one short bay.
▸How many fence panels do I need?
Divide each side's length by the panel width (usually 8 ft for wood, 6 ft for vinyl) and round up, then subtract one panel's worth for each gate. You need one post per panel plus one at each end, corner and gate.
▸How many ties for a chain link fence?
Roughly one tie per foot of height on each line post, plus one every 2 ft along the top rail. A 4 ft fence with 20 line posts and 200 ft of rail needs about 180 ties.
Last updated November 2026. Results are estimates for planning and budgeting. Footing sizes, depths and reinforcement must meet your local building code. Check with your building department, and use a licensed engineer for anything structural you're unsure about.